If the freedom of speech is taken away then dumb and silent we may be led, like sheep to the slaughter.

- George Washington

Showing posts with label motorcycle accessories. Show all posts
Showing posts with label motorcycle accessories. Show all posts

Thursday, 5 January 2012

Sparkbright Products Voltage Monitor



I've been meaning to do a post about this for a while, but tomorrow always seemed a good time to do it.

A few months ago, on the advice of someone on an internet forum (yeah, I know) I bought an LED voltage monitor on eBay. The reasoning was this: a couple of years ago, both bikes died on me in the same week. Curiously, for the same reason - a failed regulator/rectifier. The Honda ST1300 died on the lane up to the house after a 50-mile ride (phew) and the Yam failed a diagnostic session with a multimeter after it had only just got me to work and back one day. In both cases, the reg/rec had failed and either no charge or a wildly varying charge was getting to the battery. In both cases, the components were replaced and the bikes ran normally afterwards, without even toasting the batteries. But it occurred to me that I had been lucky, and if this had happened a long way from home I would have been in a right pickle. Early warning of a failure could have prevented a lot of grief.

I started to look for a dial-type voltmeter when someone suggested this indicator LED. It's made by a guy in Glasgow, and everyone on the forum who had bought one raved about it. It's hard to find a place for a dial-type gauge on a bike anyway, so I punted a tenner on one (actually a twenty, cos I bought one for each bike - and I haven't got round to fitting it to the Sprint yet).

Link to the product here. Sparkbright Products shop here.

It's a three-colour LED (red, amber and green) and it displays the bike's system voltage as follows:

Voltage Output
>15.20 Green/Red alternating (over-voltage)
>13.20 Green (charging)
>12.45 Amber (75% plus)
>12.25 Red slow flash (50% approx)
>12.00 Red 2 flashes, repeat
>11.80 Red 3 flashes, repeat
<11.80 Red 4 flashes, repeat

I mounted it on the bike next to the instruments, but (as it is constantly on when running) out of my direct line of sight. This is the position:



And this is the light when it's working (it's red because the engine isn't running and the battery is half-dead after a lot of circuit testing):



When I fitted it, I just fastened it to the clocks with insulating tape and pushed the wires into a switched live and the indicator earth - a temporary arrangement to see if it would work. It did.

In fact, it is very reassuring. It stays green for 99% of the time, and shows amber for a couple of seconds every so often. So I am in the golden 13-15V area for most of the time, and the voltage dips into the 12V area occasionally. I anticipated that this might happen, as the connections to the bike's electrics are hardly robust and may well be a bit flaky. And, let's face it, the XT is a shed - 99% good is 50% better than I have the right to expect. But the key thing for me was that it stayed green even with the lights on. It's an old-skool thing, from the days of dynamos, but I always have the sneaking suspicion that having the lights on is draining the battery. It isn't.

Today, I have been checking all the wiring and the earths on the XT to try to locate an intermittent and peculiar fault, and I decided to make an honest component of it and wire it in permanently while the tank and the plastics were off. A longer earth wire was soldered on and connected to the battery negative, and I used a Scotchlok (yeah, I know) to tap into a switched live at the ignition switch.

All seems well, although a true test will be the commute to work tomorrow night. Will it stay green all the way? Watch this space. In fact, I suspect it has already proved itself. On the two journeys between home and work before the intermittent fault appeared, it was going to amber far more often then usual, indicating that the voltage is dropping lower than it should. The bike's performance remains the same with no cause for concern, but perhaps this little device was giving me an early warning of trouble?

As far as the product itself goes, I would recommend it wholeheartedly. It's well-made, robust and waterproof, and the wires to connect it are neatly tinned. It seems to work perfectly. Running along with the light showing green is reassuring, and (hopefully) I will know about any charging problems before they leave me by the side of the road. The maker, Dr Andrew Ferguson, is a helpful guy, and his communication is personal and friendly. I will probably fit one to every bike I own from now on, as a tenner is not much to pay for peace of mind. The only thing I would do differently is that next time I will get a smaller unit. The 10mm standard bulb is a bit too big for something that is on all the time, when all you need is a speck of light in the corner of your eye. When I mount the other one to the Sprint, I will be careful to mount it well out of my line of sight, as it can be distracting, especially at night. Next time, I will probably go for the 5mm version.

Highly recommended.

Monday, 5 December 2011

Sweet! (or should that be 'suite'?)



I wrote recently about getting a new larger Givi topbox to match the small one that came with the Sprint. I now have two bikes with identical mounting plates, and two differently-sized* boxes. This is majorly convenient and adaptable: short trips and commutes on either bike, and longer trips or shopping expeditions on either bike. It's working well.

One thing remained: the keys. I usually attach the topbox keys to the ignition keys, as I would always be forgetting them otherwise. Swapping boxes over would therefore mean a lot of struggling and broken nails with swapping the keys to the other ignition set, and that just looks like a hassle too far for a system that was meant to be easy and convenient. Having the box keys on separate rings with a carabiner clip would be easier, but would mean labelling it all, and a lot of metalwork clanking about while the bike was in motion. No, that won't do either.

The other issue was the lack of a spare key for the small box. The Sprint came with one set of keys and a promise that the spare set were with the previous owner and would be found as soon as possible. I get a bit nervous if I don't have a spare set somewhere, so I pressed the dealer to get them from the previous owner (I was assured they were there and 'just forgotten'). However, after a lot of nagging and a series of variably-plausible excuses, I have come to realise that the spare set are not recoverable. A spare Triumph ignition key is on order and should be easily sorted, but a spare Givi key is not so easy. After a fair bit of research, it seems that Givi no longer sell individual keys. You have to buy a new lock.

You know that cheesy inspirational thing about when life gives you lemons, make lemonade? Well, I think I have just produced a pint ot two. For fourteen of your Earth pounds (£17 including postage), you can get a two-lock set: two barrels, two lock housings, two circlips and four keys. I ordered some from Motorcycle Planet after checking the part number of the set I needed with Givi - part number Z227, if anyone's interested - and a few days later they arrived. I was a bit nervous about fitting them. After all, it's locks, and that means deliberately difficult with some designed-in gotchas, doesn't it? But in the end it was simple, and I changed the locks in both boxes in about half an hour. The first one took 25 minutes, the second five, so that shows how easy it was after you have worked out what to do. And that included cleaning out road muck from the attachment mechanisms as well, and a quick lube of the relevant bits.

I'm not going to detail the procedure here, for obvious reasons. Suffice it to say that once you have the box off the bike and open, it's completely logical. I needed a cross-point screwdriver, a small electrical screwdriver (for the E-clip holding the thing together) and a pair of needle-nose pliers to snap it all back. You will need strong hands, too. Both for re-assembling the lock and for re-attaching it to the box, you need to hold things together against spring pressure, and on each lock I had to re-attach the lock to the box twice (lining it up better the second time) to get it to work.

Two words of warning:
  1. Before you take the E-clip off to release the lock mechanism, memorise how the thing looks, or even better take a photo. It can go back in at least 8 different orientations, and only one of those will work.
  2. Check the mechanism clamping the lid down, and the operation of the lock and attachment release before closing the box to check your work. If it closes and you have got it wrong, it's likely you will need to drill the lock out to open it again.
So now I have a set of keys for each bike, each with a Givi key that will open either box. Oh, and two spares. I believe that the modern term for this is 'suiting' the locks, but I just think it's sweet.



*See how I avoided giving offence there?

Friday, 12 August 2011

New screen



Looks much better than the old one.

Just sayin'.




Thursday, 11 August 2011

Screens, old and new

When I got the Sprint, it came with a rather strange windscreen which turned up at the top, almost vertically. I now realise that this is a proper Triumph accessory screen, named with great originality and wit "Triumph Higher Screen, Tinted" (officers, for the use of), costing a huge £116. I didn't like the appearance, and in practice it is a mixed blessing. It is awesomely good at keeping the wind off the rider. Even at highly-illegal speeds (on a closed track with trained, professional riders, of course) riding behind it was eerily calm with almost no wind pressure at all. Unfortunately, with that undoubted benefit came the worst wind noise I have ever had on a bike. It was unrelenting and harsh. At any speed over 60 mph, I could not hear either the exhaust or the engine - just the chaotic blast of white noise in my 70s-rock-deafened ears. It looked somehow wrong, too - the Sprint is pretty sleek and racy, and this looked like it belonged on a 30-year-old BMW tourer*. One member of a forum I visit called it 'nerdy', and I have to agree. It's, how you say, sensible, like a Pakamac on a supermodel.

On the same forum was a guy in Taunton who offered to swap. He was 6'4" and needed a higher screen; he had in his garage a double-bubble screen which he didn't want. Strangely, a double-bubble screen was what I did want, so we agreed to exchange. I received the DB screen yesterday and put it on the bike. It looks a million times better. I haven't had a chance to test it on the road yet, but I'm hopeful that it will be quieter, even if it lets a bit more wind through. But from an appearance point of view it is already a success. I'll be sending the other one off to Taunton as soon as the guy lets me know he is home and able to receive it.

Before:



After:



*Not that there's anything wrong with those. But horses for courses, and all that.
Related Posts Plugin for WordPress, Blogger...